/*
* Copyright (c) 2015 Intel Corporation
*
* SPDX-License-Identifier: Apache-2.0
*/
#ifndef __INC_BOARD_H
#define __INC_BOARD_H
#include <board_cfg.h>
#include <drivers/audio/audio_common.h>
#include <soc.h>
/*Configure GPIO high resistance before sleep and restore GPIO after wakeup */
#define SLEEP_GPIO_REG_SET_HIGHZ \
/*sensor*/ \
/*//GPION_CTL(18), not use defaut highz*/ \
/*//GPION_CTL(20), not use defaut highz*/ \
GPION_CTL(25), /*audio PA1_EN */ \
GPION_CTL(26), /*TP_PWR */ \
/*TP*/ \
/*//GPION_CTL(26), not use defaut highz*/ \
/* //GPION_CTL(27), not useļ¼defaut highz*/ \
GPION_CTL(49), /*tp rst*/ \
GPION_CTL(50), /*tp irq*/ \
/*i2c0 charger */ \
GPION_CTL(57), /*not use in sleep*/ \
GPION_CTL(58), /*not use in sleep*/ \
/*i2c3 audio PA/LCD I2c/Electricity meter*/ \
GPION_CTL(51), /*not use in sleep*/ \
GPION_CTL(52), /*not use in sleep*/ \
#define CONFIG_SD_USE_GPIO_DET 0
#define CONFIG_SD_GPIO_DET_NUM 64 /*GPIO64*/
#define CONFIG_SD_GPIO_DET_LEVEL 0 /* The GPIO level(0: low voltage 1:high voltage) to indicates the SD card has been detected */
#define CONFIG_SD_USE_GPIO_POWER 1
#define CONFIG_SD_GPIO_POWER_NUM 64 /*GPIO64*/
#define CONFIG_SD_GPIO_POWER_LEVEL 0 /* The GPIO level(0: low voltage 1:high voltage) to indicates the SD/eMMC card power on */
#define CONFIG_TPKEY_GPIO_ISR_NUM 50
#define CONFIG_TPKEY_GPIO_SCL_NUM 51
#define CONFIG_TPKEY_GPIO_SDA_NUM 52
#define CONFIG_PANEL_TE_GPIO GPIO_CFG_MAKE(CONFIG_GPIO_B_NAME, 3, GPIO_ACTIVE_HIGH, 1)
#define CONFIG_PANEL_RESET_GPIO GPIO_CFG_MAKE(CONFIG_GPIO_B_NAME, 0, GPIO_ACTIVE_LOW, 1)
//#define CONFIG_PANEL_POWER_GPIO GPIO_CFG_MAKE(CONFIG_GPIO_B_NAME, 1, GPIO_ACTIVE_HIGH, 1)
#define CONFIG_PANEL_POWER1_GPIO GPIO_CFG_MAKE(CONFIG_GPIO_A_NAME, 21, GPIO_ACTIVE_HIGH, 1)
#define CONFIG_TPKEY_ISR_GPIO GPIO_CFG_MAKE(CONFIG_GPIO_B_NAME, 18, GPIO_ACTIVE_LOW, 1)
#define CONFIG_TPKEY_RESET_GPIO GPIO_CFG_MAKE(CONFIG_GPIO_B_NAME, 17, GPIO_ACTIVE_LOW, 1)
//#define CONFIG_TPKEY_POWER_GPIO GPIO_CFG_MAKE(CONFIG_GPIO_A_NAME, 26, GPIO_ACTIVE_HIGH, 1)
#if IS_ENABLED(CONFIG_GPIOKEY)
/* The GPIO MFP for GPIO KEY */
#if CONFIG_GPIOKEY_PRESSED_VOLTAGE_LEVEL
#define CONFIG_GPIOKEY_MFP PIN_MFP_SET(GPIO_24, GPIOKEY_MFP_CFG)
#else
#define CONFIG_GPIOKEY_MFP PIN_MFP_SET(GPIO_24, GPIOKEY_MFP_PU_CFG)
#endif
#endif
#define CONFIG_SPINAND_USE_GPIO_POWER 1
#define CONFIG_SPINAND_POWER_GPIO 64 /* GPIO64 */
#define CONFIG_SPINAND_GPIO_POWER_LEVEL 1 /* The GPIO level(0: low voltage 1:high voltage) to indicates the spinand power on */
#define CONFIG_SPINAND_DATA 0 /* SPINand Flash Use for data or boot; 0:boot; 1:data */
/* ACC Sensor GPIO Config */
#define CONFIG_SENSOR_ACC_POWER_GPIO 0
#define CONFIG_SENSOR_ACC_RESET_GPIO 0
#define CONFIG_SENSOR_ACC_ISR_GPIO 54 /* GPIO54 */
#define CONFIG_SENSOR_ACC_TRIG_IO 5 /* PPI_triger5 */
/* Heart-rate Sensor GPIO Config */
#define CONFIG_SENSOR_HR_POWER_GPIO 22 /* GPIO22 */
#define CONFIG_SENSOR_HR_RESET_GPIO 0 /* GPIO62 */
#define CONFIG_SENSOR_HR_ISR_GPIO 74 /* GPIO74 */
#define CONFIG_SENSOR_HR_TRIG_IO 6 /* PPI_triger6 */
/* Magnet Sensor GPIO Config */
#define CONFIG_SENSOR_MAG_POWER_GPIO 0
#define CONFIG_SENSOR_MAG_RESET_GPIO 0
#define CONFIG_SENSOR_MAG_ISR_GPIO 0
#define CONFIG_SENSOR_MAG_TRIG_IO 0
/* Baro Sensor GPIO Config */
#define CONFIG_SENSOR_BARO_POWER_GPIO 0
#define CONFIG_SENSOR_BARO_RESET_GPIO 0
#define CONFIG_SENSOR_BARO_ISR_GPIO 0
#define CONFIG_SENSOR_BARO_TRIG_IO 0
#define BOARD_BATTERY_CAP_MAPPINGS \
{0, 3200}, \
{5, 3300}, \
{10, 3400}, \
{20, 3550}, \
{30, 3650}, \
{40, 3750}, \
{50, 3800}, \
{60, 3850}, \
{70, 3900}, \
{80, 3950}, \
{90, 4000}, \
{100, 4050},
#define BOARD_ADCKEY_KEY_MAPPINGS \
{KEY_ADFU, 0x05}, \
{KEY_PREVIOUSSONG, 0x376}, \
{KEY_MENU, 0x532}, \
{KEY_TBD, 0x69C}, \
{KEY_VOLUMEDOWN, 0x86D}, \
{KEY_VOLUMEUP, 0x9EE}, \
{KEY_NEXTSONG, 0xB87},
/* @brief The macro to define an audio device */
#define AUDIO_LINE_IN0 (AUDIO_DEV_TYPE_LINEIN | 0)
#define AUDIO_LINE_IN1 (AUDIO_DEV_TYPE_LINEIN | 1)
#define AUDIO_LINE_IN2 (AUDIO_DEV_TYPE_LINEIN | 2)
#define AUDIO_ANALOG_MIC0 (AUDIO_DEV_TYPE_AMIC | 0)
#define AUDIO_ANALOG_MIC1 (AUDIO_DEV_TYPE_AMIC | 1)
#define AUDIO_ANALOG_MIC2 (AUDIO_DEV_TYPE_AMIC | 2)
#define AUDIO_ANALOG_FM0 (AUDIO_DEV_TYPE_FM | 0)
#define AUDIO_DIGITAL_MIC0 (AUDIO_DEV_TYPE_DMIC | 0)
#define AUDIO_DIGITAL_MIC1 (AUDIO_DEV_TYPE_DMIC | 1)
struct board_pinmux_info{
const struct acts_pin_config *pins_config;
int pins_num;
};
struct pwm_acts_pin_config{
unsigned int pin_num;
unsigned int pin_chan;
unsigned int mode;
};
struct board_pwm_pinmux_info{
const struct pwm_acts_pin_config *pins_config;
int pins_num;
};
extern void board_get_mmc0_pinmux_info(struct board_pinmux_info *pinmux_info);
extern void board_get_spdiftx0_pinmux_info(struct board_pinmux_info *pinmux_info);
extern void board_get_spdifrx0_pinmux_info(struct board_pinmux_info *pinmux_info);
extern void board_get_i2stx0_pinmux_info(struct board_pinmux_info *pinmux_info);
extern void board_get_pwm_pinmux_info(struct board_pwm_pinmux_info *pinmux_info);
extern void board_get_spinand_pinmux_info(struct board_pinmux_info *pinmux_info);
extern void board_get_spinand_gpiohighz_info(struct board_pinmux_info *pinmux_info);
extern void board_set_ntc_pinmux_info(bool enable, bool use_as_ntc);
#if 1
/* @brief Get the mapping relationship between the hardware inputs and audio devices */
int board_audio_device_mapping(audio_input_map_t *input_map);
int board_extern_pa_ctl(u8_t pa_class, bool is_on);
#endif
#ifdef CONFIG_PANEL
void board_lcd_suspend(bool aod_en, bool early_suspend);
void board_lcd_resume(bool aod_en, bool late_resume);
#endif
#endif /* __INC_BOARD_H */