source ./aps/customer/Kconfig.frontend source ./aps/customer/Kconfig.external source ./aps/customer/Kconfig.storage source ./aps/customer/Kconfig.hdmi menu "AUDIO IO Select" config HEADPHONE bool "SUPPORT HEADPHONE" default y if(HEADPHONE) choice prompt "headphone detect method" default HEADPHONE_DETECT_BY_ISR config HEADPHONE_DETECT_BY_ISR bool "HEADPHONE_DETECT_BY_ISR" config HPDET_BY_SWTIMER bool "HEADPHONE_DETECT_BY_SWPOLLING" endchoice endif choice prompt "Select Headphone use ic pin" default HP_OUT_NONE config HP_OUT_FROM_SPEAKER_PIN bool "Heaphone out use speaker pin" config HP_OUT_FROM_HP_PIN bool "Heaphone out use HP pin" config HP_OUT_FROM_LINEOUT_PIN bool "Heaphone out use lineout pin" config HP_OUT_NONE bool "none headphone" endchoice config DAC1_SRC_TYPE int prompt "DAC1 Source , 0:SD0(Speaker) 1: SD1(Lineout)" default 0 config DAC2_SRC_TYPE int prompt "DAC2 Source , 0:SD0(Speaker) 1: SD1(Lineout)" default 1 config SUPPORT_SPDIF_OUT bool prompt "Support SPDIF Out" default y config AUDIO_ADC_12K_CIRCUIT bool prompt "AUDIO ADC GAIN FOR 12ohm and 12Kohm CIRCUIT" default n help AUDIO ADC GAIN FOR 12ohm and 12Kohm CIRCUIT config AUDIO_ADC_43K_CIRCUIT bool prompt "AUDIO ADC GAIN for 43K ohm input circuit" default n help AUDIO ADC GAIN FOR 12ohm and 12Kohm CIRCUIT config FOR_AV2_AUDIO_ADC_12K_CIRCUIT bool prompt "AV2 SOURCE AUDIO ADC GAIN FOR 12ohm and 12Kohm CIRCUIT" default n help AV2 SOURCE AUDIO ADC GAIN FOR 12ohm and 12Kohm CIRCUIT endmenu config EXTRA_PWM_CONTROL_FOR_FAN bool "Extra PWM Control For Fan" default n help use pwm control rotate speed config KEYPAD0_DISABLE bool prompt "Keypad0 disable" default n config KEYPAD1_FUNCTION bool prompt "Keypad1 disable" default y menu "Kaypad1 disable select" depends on KEYPAD1_FUNCTION config KEYPAD1_DISABLE bool "Disable keypad1 for driver " default y config KEYPAD1_DISABLE_BOOT bool "Disable keypad1 for boot" default y endmenu config SKIP_AC_POWERKEY bool prompt "Keypad0 skip AC power key" default n config KEYPAD_SINGLE_REUSE bool prompt "Support Single Keypad(need config SUPPORT_HELP_MENU)" default y if CV512CH_X42_FORMAL___DEFAULTPROJ__CULTRAVIEW__CULTRAVIEW__CULTRAVIEW config KEYPAD_THREE_KEY_REUSE bool prompt "Support ThreeKey keypad" default n config KEYPAD_FIVE_KEY_REUSE bool prompt "Support FiveKey keypad(need config SUPPORT_HELP_MENU)" default n config TUNER_USE_AGC2 bool prompt "Tuner Use AGC2 Control" default n config GLED_DISABLE bool prompt "Single LED mode" default n help Use one GPIO/PWM control RED and GREEN LED config MNT_LED depends on !GLED_DISABLE bool prompt "Monitor LED mode" default n help Use two GPIO control RED and GREEN LED config GLED_CTRL_INV depends on MNT_LED bool prompt "G LED control invert" default n help GLED control invert config CONTROL_STANDBY_LED bool prompt "Control Standby LED" default n help Control Standby LED by user setting config MAINPOWER_SEQUENCE_CTRL bool prompt "Main Power Sequence after AUX 1V" default n help Use GPIO34 contorl main power sequence config MAINPOWER_SEQUENCE_SW_CTRL bool prompt "SW Main Power Sequence after AUX 1V " default n help Use CONFIG_MAINPOWER_3V3_CTRL_PIN contorl main power sequence config MAINPOWER_3V3_CTRL_PIN depends on MAINPOWER_SEQUENCE_SW_CTRL int prompt "3V3 main power control pin" default 27 config MAINPOWER_3V3_SW_DELAY_TIME depends on MAINPOWER_SEQUENCE_SW_CTRL int prompt "3V3 main power control delay time" default 5 config PANEL_BL_ON_BL_ADJ_SWAP_FUNCTION bool prompt "BL_ON as PWM2 and BL_ADJ as GPIO mode" default n config PANEL_BACKLIGHT_DIM_REF bool prompt "Panel backlight control via DIM and REF" default n config PANEL_ON_REF_TO_DIM_DELAY depends on PANEL_BACKLIGHT_DIM_REF int prompt "Panel power on delay between REF to DIM (30 ms)" default 30 config PANEL_OFF_DIM_TO_REF_DELAY depends on PANEL_BACKLIGHT_DIM_REF int prompt "Panel power off delay between DIM to REF (30 ms)" default 30 config PANEL_PWM_REF_INV depends on PANEL_BACKLIGHT_DIM_REF bool prompt "PWM REF invert circuit" default n config PANEL_PWM_DIM_PERIOD depends on PANEL_BACKLIGHT_DIM_REF int prompt "PWM DIM period (default 200 HZ)" default 200 config PANEL_PWM_DIM_DUTY depends on PANEL_BACKLIGHT_DIM_REF int prompt "PWM DIM duty (default 80%)" default 80 config PANEL_PWM_REF_DUTY depends on PANEL_BACKLIGHT_DIM_REF int prompt "PWM REF duty (default 40%)" default 40 config PANEL_PWM_REF_PERIOD depends on PANEL_BACKLIGHT_DIM_REF int prompt "PWM REF period (default 25k HZ)" default 25000 config PANEL_SEQE_POWEROFF_ADJ_EARLY_BLON bool prompt "Panel Poweroff Sequence ADJ earlier than BL_ON" default n config PANEL_SEQE_POWEROFF_ADJ_GPIO_MODE bool prompt "Panel Poweroff Sequence ADJ pin need set to GPIO mode" default n config PANEL_ADJ_INVERT bool prompt "Panel backlight ADJ control invert" default n config AV_ON_G_CHANNEL bool prompt "AV Signals on ADC G Channel" default n config CRYSTAL_USE_24MHZ bool prompt "Crystal Use 24MHZ(For Internal Test Only)" default n config SUPPORT_USB3_CONNECTOR bool prompt "Support USB3.0 connector" default n config FIB_FOR_AV_ON_533_A0 bool prompt "FIB for AV testing on 533 A0 Chip(For Internal Test Only)" default n config ATV_ESD_COLOR_SOUND_ISSUE bool prompt "ATV ESD COLOR SOUND ISSUE for 512C" default n menu "Update LED Style" config GREEN_LED_FLASH bool prompt "Green LED flash duing update" default n config RED_LED_FLASH bool prompt "Red LED flash duing update" default y endmenu menu "8506 TCON Setting" config SUPPORT_TCON bool "Support TCON" default n config USE_TCON_OUTPUT bool "Using TCON Output" default n config ENABLE_TCON_OVERDRIVE bool "Enable TCON Over Drive" default n #config ENABLE_TCON_DEMURA_TABLE # bool "Enable TCON Demura Table" # default n choice prompt "TCON PANEL Select" default TCON_NONE config TCON_NONE bool "None" config BOE_HV320WHB_N86 bool "BOE HV320WHB N86" config BOE_HV320WHB_N56 bool "BOE HV320WHB N56" config BOE_HV320WHB_N81 bool "BOE HV320WHB N81" config BOE_HV430FHB_N40 bool "BOE HV430FHB N40" config CSOT_ST3151A05_C bool "CSOT ST3151A05 C" config HKC_PT320AT01_4 bool "HKC PT320AT01 4" endchoice choice prompt "TCON BOARD Select" config TCON_BOARD_DEFAULT bool "Default" config TCON_BOARD_8506T128PIN bool "RDA_8506T 128 Pin" config TCON_BOARD_6710T bool "UTS_6710T" endchoice config TCON_BIN_FOLDER_NAME string default "BOE_N86/RDA_8506T" if BOE_HV320WHB_N86 && TCON_BOARD_DEFAULT default "BOE_N86/RDA_8506T_128" if BOE_HV320WHB_N86 && TCON_BOARD_8506T128PIN default "BOE_N86/UTS_6710T" if BOE_HV320WHB_N86 && TCON_BOARD_6710T default "BOE_N56/RDA_8506T" if BOE_HV320WHB_N56 && TCON_BOARD_DEFAULT default "BOE_N56/RDA_8506T_128" if BOE_HV320WHB_N56 && TCON_BOARD_8506T128PIN default "BOE_N56/UTS_6710T" if BOE_HV320WHB_N56 && TCON_BOARD_6710T default "BOE_N81/RDA_8506T" if BOE_HV320WHB_N81 && TCON_BOARD_DEFAULT default "BOE_N81/RDA_8506T_128" if BOE_HV320WHB_N81 && TCON_BOARD_8506T128PIN default "BOE_N81/UTS_6710T" if BOE_HV320WHB_N81 && TCON_BOARD_6710T default "BOE_N40/RDA_8506T" if BOE_HV430FHB_N40 && TCON_BOARD_DEFAULT default "BOE_N40/RDA_8506T_128" if BOE_HV430FHB_N40 && TCON_BOARD_8506T128PIN default "BOE_N40/UTS_6710T" if BOE_HV430FHB_N40 && TCON_BOARD_6710T default "CSOT_C/RDA_8506T" if CSOT_ST3151A05_C && TCON_BOARD_DEFAULT default "CSOT_C/RDA_8506T_128" if CSOT_ST3151A05_C && TCON_BOARD_8506T128PIN default "CSOT_C/UTS_6710T" if CSOT_ST3151A05_C && TCON_BOARD_6710T default "HKC_PT320AT01_4" if HKC_PT320AT01_4 endmenu menu "LVDS Setting" config LVDS_SINGLE_LANE_PAIR_SETTING hex prompt "LVDS Single Channel Setting(for 8506/6710)" default 0x40f help #define LVA0 0x1 //LVA #define LVA1 0x2 #define LVA2 0x4 #define LVA3 0x8 #define LVA4 0x10 // 10 bit panel LVA A #define LVB0 0x20 // LVB #define LVB1 0x40 #define LVB2 0x80 #define LVB3 0x100 #define LVB4 0x200 // 10 bit panel LVB B #define LV_CLK 0x400 // lvds clk ch PS:Calc Vaule according to hw design,if has used channel need to set 1 config LVDS_DUAL_LANE_PAIR_SETTING hex prompt "LVDS Dual Channel Setting(for 8506/6710)" default 0x5ef help #define LVA0 0x1 //LVA #define LVA1 0x2 #define LVA2 0x4 #define LVA3 0x8 #define LVA4 0x10 // 10 bit panel LVA A #define LVB0 0x20 // LVB #define LVB1 0x40 #define LVB2 0x80 #define LVB3 0x100 #define LVB4 0x200 // 10 bit panel LVB B #define LV_CLK 0x400 // lvds clk ch PS:Calc Vaule according to hw design,if has used channel need to set 1 endmenu menu "Board USB 5V VCC" config USBVCC_USE_GPIO bool prompt "Using GPIO to control USB VCC" default n config GPIO_USB5V depends on USBVCC_USE_GPIO int prompt "usb 5v power control gpio decimal number" default 16 config GPIO_USB5V_LEVEL depends on USBVCC_USE_GPIO int prompt "0:low ; 1:high" default 1 endmenu